Install the Y Assembly

Written By: Filip Goc
  • Comments: 2
  • Favorites: 0

Difficulty

Moderate

Steps

57

Time Required

Suggest a time??

Sections

6

Flags

1

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Introduction

Not the guide you are looking for?

Go back to the ⇤ Makers Kit Build Flow.

Video Overview

  1. Edit
  2. Edit

  3. M2x12 (these are the tiniest) M2x12 (these are the tiniest)

    • M2x12 (these are the tiniest)

    Edit
  4. Edit

  5. The switch reed needs to point towards left. The switch reed needs to point towards left. The switch reed needs to point towards left.

    • The switch reed needs to point towards left.

    Edit

  6. [Update] This zip tie (and the holes in the Bottom) was removed in early 2018 to speed up the build. Simply skip it. [Update] This zip tie (and the holes in the Bottom) was removed in early 2018 to speed up the build. Simply skip it. [Update] This zip tie (and the holes in the Bottom) was removed in early 2018 to speed up the build. Simply skip it.

    • [Update] This zip tie (and the holes in the Bottom) was removed in early 2018 to speed up the build. Simply skip it.

    Edit
  7. Edit
  8. Edit
  9. Edit
  10. Edit
  11. Edit
  12. Edit
  13. Edit
  14. Edit
  15. Edit

  16. Point the motor connector towards right. Point the motor connector towards right. Point the motor connector towards right.

    • Point the motor connector towards right.

    Edit

  17. Check ✓ Check ✓

    • Check ✓

    Edit
  18. Edit
  19. Edit
  20. Edit
  21. Edit
  22. Edit

  23. Check ✓

    • Check ✓

    Edit
  24. Edit
  25. Edit
  26. Edit
  27. Edit
  28. Edit
  29. Edit
  30. Edit
  31. Edit
  32. Edit
  33. Edit
  34. Edit
  35. Edit

  36. Tighten well. This is metal-on-metal tightening, so you do not have to be as gentle as usual.

    • Tighten well.

    • This is metal-on-metal tightening, so you do not have to be as gentle as usual.

    Edit
  37. Edit
  38. Edit
  39. Edit
  40. Edit
  41. Edit
  42. Edit
  43. Edit
  44. Edit
  45. Edit

  46. Be gentle. Do no force the rods and keep them straight or you may damage the ball bearing by knocking some balls out. Be gentle. Do no force the rods and keep them straight or you may damage the ball bearing by knocking some balls out.

    • Be gentle. Do no force the rods and keep them straight or you may damage the ball bearing by knocking some balls out.

    Edit

  47. Check ✓ Check ✓

    • Check ✓

    Edit
  48. Edit
  49. Edit

  50. Place your JellyBOX over the edge of a table. Place your JellyBOX over the edge of a table.

    • Place your JellyBOX over the edge of a table.

    Edit
  51. Edit
  52. Edit
  53. Edit
  54. Edit
  55. Edit
  56. Edit

    • ▶ Video: Y Mechanical Checkpoint (25s)

    • Do not move too fast. You are generating current by forcing the motor to rotate. If you generate too much current, you could damage your electronics; namely the drivers.

    • Make sure that the Y EndStop gets engaged by one of a Y Assembly bearings. There's an audible click.

    • Make sure the Y assembly is moving smoothly.

    Edit
Conclusion

What's Next?

Get back to the ⇤ Makers Kit Build Flow and continue with the next guide.

Author

Filip Goc

Member since: 01/14/2016

18,037 Reputation

490 Guides authored

Team

team curriculum Member of team curriculum

2 Members

490 Guides authored

0 Comments

Add Comment