Install the X Assembly

Written By: Filip Goc (and one other contributor)
  • Comments: 1
  • Favorites: 0

Difficulty

Moderate

Steps

46

Time Required

Suggest a time??

Sections

2

Flags

1

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

  1. Edit
  2. Edit
  3. Edit

  4. Leave the zip ties loose. Leave the zip ties loose. Leave the zip ties loose.

    • Leave the zip ties loose.

    Edit
  5. Edit
  6. Edit
  7. Edit
  8. Edit
  9. Edit

  10. Be gentle. Do no force the rod and keep it straight or you may damage the ball bearing by knocking some balls out. Be gentle. Do no force the rod and keep it straight or you may damage the ball bearing by knocking some balls out. Be gentle. Do no force the rod and keep it straight or you may damage the ball bearing by knocking some balls out.

    • Be gentle. Do no force the rod and keep it straight or you may damage the ball bearing by knocking some balls out.

    Edit
  11. Edit

  12. BE GENTLE. Do no force the rod and keep it straight or you may damage the inside of the bearing. BE GENTLE. Do no force the rod and keep it straight or you may damage the inside of the bearing. BE GENTLE. Do no force the rod and keep it straight or you may damage the inside of the bearing.

    • BE GENTLE. Do no force the rod and keep it straight or you may damage the inside of the bearing.

    Edit

    • We highly recommend you scroll ahead and look at the whole procedure of zip tying the x assembly.

    • The procedure is quite simple, but it's hard to understand if you look image-by-image.

    • We'll first tighten both front zip ties, and only then both zip ties in the back.

    Edit
  14. Edit

  15. Note that on the left the rod is outside, while on the right the rod is inside. Note that on the left the rod is outside, while on the right the rod is inside.

    • Note that on the left the rod is outside, while on the right the rod is inside.

    Edit

  16. Push the rods in place and tighten the back zip ties. Push the rods in place and tighten the back zip ties. Push the rods in place and tighten the back zip ties.

    • Push the rods in place and tighten the back zip ties.

    Edit
  17. Edit

  18. The X assembly is inserted.

    • The X assembly is inserted.

    Edit

  19. Turn the JellyBOX from its back into normal position. Turn the JellyBOX from its back into normal position.

    • Turn the JellyBOX from its back into normal position.

    Edit
  20. Edit
  21. Edit

  22. Leave the zip tie loose. Leave the zip tie loose. Leave the zip tie loose.

    • Leave the zip tie loose.

    Edit

    • ▶ Video: Adjust the X Wire Harness Folding (50s)

    • Adjust the mounting point as needed so that the harness is folding nicely and predictably.

    Edit
  24. Edit
  25. Edit
  26. Edit
  27. Edit

  28. In short, connect all the wires according to their labels. We'll start on the left.

    • In short, connect all the wires according to their labels. We'll start on the left.

    Edit
  29. Edit

  30. Make sure to match plus with plus... Make sure to match plus with plus... Make sure to match plus with plus...

    • Make sure to match plus with plus...

    Edit

  31. ... and minus with minus.

    • ... and minus with minus.

    Edit
  32. Edit

  33. Make sure to match plus with plus and minus with minus. Make sure to match plus with plus and minus with minus. Make sure to match plus with plus and minus with minus.

    • Make sure to match plus with plus and minus with minus.

    Edit

  34. This 12V line powers up the Z Probe and the Hotend fan.

    • This 12V line powers up the Z Probe and the Hotend fan.

    Edit
  35. Edit
  36. Edit
  37. Edit
  38. Edit
  39. Edit
  40. Edit
  41. Edit
  42. Edit
  43. Edit
  44. Edit
  45. Edit
  46. Edit
Conclusion

You have installed the X assembly. This is arguably the longest and most complicated part of the whole build, so, kudos!

Author

with 1 other contributor

Filip Goc

Member since: 01/14/2016

18,037 Reputation

490 Guides authored

Team

team curriculum Member of team curriculum

2 Members

490 Guides authored

One Comment

The pictures in steps 44, 45, & 46 (as well as those in ch. 09 part 01 steps 11 & 12) show the T0 cable with the pink/red wire on the left & the black wire on the right. Are these images correct ? (And does it matter for this cable? I notice the wires of the T1 cable are not color coded.)

The cables I received for 10 Easy Kit Heated JellyBOX v2.1.b.b.2 are all stickered so that, if the label sticker faces up, the T0 black wire is on the left and the pink/red is on the right.

Thanks.

Terrilynn Platt - Reply

Add Comment